Get Ready to Pass the HPE6-A85 exam Right Now Using Our ACA Campus Access Associate Exam Package

Enhance Your Career With Available Preparation Guide for HPE6-A85 Exam

NEW QUESTION # 11
A network technician is troubleshooting one new AP at a branch office that will not receive Its configuration from Aruba Central The other APs at the branch are working as expected The output of the 'show ap debug cloud-server command' shows that the "cloud conflg received" Is FALSE.
After confirming the new AP has internet access, what would you check next?

• A. Verify the AP has a license assigned
• B. Disable and enable Aruba Central to trigger configuration refresh
• C. Disable and enable activate to trigger provisioning refresh
• D. Verify the AP can ping the device on arubanetworks.com

Answer: A

Explanation:
Explanation
If the AP has internet access but does not receive its configuration from Aruba Central, one possible reason is that the AP does not have a license assigned in Aruba Central. A license is required for each AP to be managed by Aruba Central.
References:https://www.arubanetworks.com/techdocs/Central/2.5.2-GA/HTML_frameset.htm#GUID-8F0E7E8B

NEW QUESTION # 12
You need to configure wireless access for several classes of loT devices, some of which operate only with 802
11b. Each class must have a unique PSK and will require a different security policy applied as a role There will be 15-20 different classes of devices and performance should be optimized Which option fulfills these requirements''

• A. Single SSID with MPSK for each loT class using 2.4GHz and 5 GHz bands
• B. Individual SSIDs with unique PSK for each loT class, using 5GHz and 6 GHz bands
• C. Single SSID with MPSK for each loT class using 5 GHz and 6 GHz bands
• D. Individual SSIDs with unique PSK for each loT class, using 2.4GHZ and 5GHz band

Answer: D

Explanation:
Explanation
The option that fulfills the requirements is to create individual SSIDs with unique PSK for each loT class, using 2.4 GHz and 5 GHz band. This option provides the following benefits:
Each loT class has a unique PSK that can be used to apply a different security policy as a role. This enhances the security and flexibility of the WLAN network.
Individual SSIDs allow for better isolation and management of different loT classes. This improves the performance and scalability of the WLAN network.
Using both 2.4 GHz and 5 GHz bands allows for backward compatibility with loT devices that operate only with 802.11b, which uses the 2.4 GHz band . It also allows for higher throughput and less interference for loT devices that support 802.11a, 802.11g, 802.11n, or 802.11ac, which use the 5 GHz band2.
The other options do not fulfill the requirements because:
Single SSID with MPSK for each loT class using 5 GHz and 6 GHz bands: This option does not support loT devices that operate only with 802.11b, which uses the 2.4 GHz band . It also does not optimize the performance of the WLAN network, as a single SSID may cause co-channel interference and congestion among different loT classes.
Single SSID with MPSK for each loT class using 2.4 GHz and 5 GHz bands: This option does not optimize the performance of the WLAN network, as a single SSID may cause co-channel interference and congestion among different loT classes.
Individual SSIDs with unique PSK for each loT class, using 5 GHz and 6 GHz bands: This option does not support loT devices that operate only with 802.11b, which uses the 2.4 GHz band1.
References: 1 https://en.wikipedia.org/wiki/IEEE_802.11b-1999 2
https://www.lifewire.com/wireless-standards-802-11a-802-11b-g-n-and-802-11ac-816553

NEW QUESTION # 13
You are in a meeting with a customer where you are asked to explain the network redundancy feature Multiple Spanning Tree (MSTP). What is the correct statement for this feature?

• A. MSTP configuration ID revision by default as switch serial number
• B. MSTP configuration ID revision by default as current MSTP root priority
• C. MSTP configuration ID name by default using switch serial number
• D. MSTP configuration ID name by default using switch IMC address

Answer: D

Explanation:
Explanation
MSTP Multiple Spanning Tree Protocol. MSTP is an IEEE standard protocol for preventing loops in a network with multiple VLANs. MSTP allows multiple VLANs to be mapped to a reduced number of spanning-tree instances. configuration ID consists of two parameters: name and revision. The name is a
32-byte ASCII string that identifies the MSTP region, which is a group of switches that share the same configuration ID and VLAN-to-instance mapping. The revision is a 16-bit number that indicates the version of the configuration ID. By default, the MSTP configuration ID name is set to the switch IMC address, which is a unique identifier derived from the MAC address Media Access Control address. MAC address is a unique identifier assigned to a network interface controller (NIC) for use as a network address in communications within a network segment. of the switch.
References:https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/mstp/

NEW QUESTION # 14
After having configured the edge switch uplink as requested your colleague says that they have failed to ping the core You ask your colleague to verify the connection is plugged in and the switch is powered on They confirm that both are correct You attempt to ping the core switch and confirm that the ping is failing.
Knowing the nature of this deployment, what commands might you use to troubleshoot this issued

• A. Ping 10.1.1.1 - ping the core to attempt to verify connectivity show lacp agg - to verify which link aggregations are currently configured using which physical ports show lacp int - to verify the LACP status and whether any links are blocking in your topology show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports show run interface 1/1/51.1/1/52-to ensure the physical interfaces are no-shut and members of the lag show run interface lag 1 - to ensure the correct vlan trunking configuration is applied to the logical interface show run int vlan 20 - to ensure you have the L3 SVI no shut and configured in the correct subnet
• B. Ping 10.11 1 - ping the core to attempt to verify connectivity Show trunk - to verify if the LAG interface was correctly added to the switch Show spanning tree - to check for spanning-tree blocked states Show port-access clients interface all - to view any port-access blocking states or failed authentication attempts on all interfaces Show run interface vlan20 - to double check the layer 3 svi configuration is correct for l_3 connectivity Show lldp neighors - to verify whether you are able to see the Core as an L2 neighbor to verify if the correct links are plugged in to the correct ports
• C. Show run - to view the running configuration of the switch Show run | begin 20 "vlan 20" - to ensure VLAN 20 was correctly added to the database show run | begin 20 'interface vlan 20' - to view the L3 SVI configuration Show run interface 1/1/51.1/1/52 - to ensure the physical interfaces are no shut and were added as members of LAG 1 Show run int lag 1 - to verify LACP mode active was configured to eliminate LACP blocking states
• D. diagnostic diag cable-diag 1/1/51 diag cable-diag 1/1/52 - to view diagnostic information for the physical link to get a status on any interruptions to Layer 1 connectivity, show ip route - to verify that the default gateway is present in the routing table show ip ospf - to check whether there is a layer 3 routing protocol enabled show ip dns - to view whether there is a valid dns source

Answer: A

Explanation:
Explanation
These commands might help troubleshoot this issue as they check various aspects of the connectivity between the edge switch and the core switch, such as Layer 3 reachability, Layer 2 adjacency, LACP configuration and status, VLAN trunking configuration, and interface status.
References:https://www.arubanetworks.com/techdocs/AOS-CX_10_04/CLI/GUID-8F0E7E8B-0F4B-4A3C-AE7

NEW QUESTION # 15
Refer to the exhibit.

In the given topology, a pair of Aruba CX 8325 switches are in a VSX stack using the active gateway What is the nature and behavior of the Virtual IP for the VSX pair if clients are connected to the access switch using VSX as the default gateway?

• A. Virtual IP uses SVI IP address synced with VSX
• B. Virtual IP is active on the primary VSX switch
  Virtual floating IP will failover in case of a failure
• C. Virtual IP is active on both CX switches

Answer: B

Explanation:
Explanation
Virtual Switching Extension (VSX) is a feature that allows two Aruba CX switches to operate as a single logical device with a single control plane and data plane. VSX provides high availability, scalability, and simplified management for campus and data center networks3. In VSX, one switch is designated as the primary switch and the other as the secondary switch. The primary switch owns and responds to ARP Address Resolution Protocol. ARP is a communication protocol used for discovering the link layer address, such as a MAC address, associated with a given internet layer address, typically an IPv4 address. This mapping is a critical function in the Internet protocol suite. requests for the virtual IP address of the VSX pair4. The virtual IP address is used as the default gateway for clients connected to the access switch. If the primary switch fails, the secondary switch takes over the virtual IP address and continues to forward traffic for the clients5.
References: 3
https://www.arubanetworks.com/techdocs/AOS-CX_10_04/UG/Content/cx-ug/vsx/vsx-overview.htm 4
https://www.arubanetworks.com/techdocs/AOS-CX_10_04/UG/Content/cx-ug/vsx/vsx-ip-addressing.htm 5
https://www.arubanetworks.com/techdocs/AOS-CX_10_04/UG/Content/cx-ug/vsx/vsx-failover.htm

NEW QUESTION # 16
When using the OSPF dynamic routing protocol on an Aruba CX switch, what must match on the neighboring devices to exchange routes?

• A. BDR configuration
• B. ECMP method
• C. DR configuration
• D. Hello timers

Answer: D

Explanation:
Explanation
OSPF Open Shortest Path First. OSPF is a link-state routing protocol that uses a hierarchical structure to create a routing topology for IP networks. OSPF routers exchange routing information with their neighbors using Hello packets, which are sent periodically on each interface. To establish an adjacency Adjacency is a relationship formed between selected neighboring routers for the purpose of exchanging routing information., OSPF routers must agree on several parameters, including Hello timers, which specify how often Hello packets are sent on an interface. If the Hello timers do not match between neighboring routers, they will not form an adjacency and will not exchange routes.
References:https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/osfp/o

NEW QUESTION # 17
What is indicated by a solid amber radio status LED on an Aruba AP?

• A. The radio is enabled in monitor or spectrum analysis mode
• B. The radio is working the 5 GHz band only.
• C. The radio is working in mesh mode
• D. Not enough PoE is provided from the switch to power both radios of the AP

Answer: A

Explanation:
Explanation
The solid amber radio status LED on an Aruba AP Access Point (AP) Access Point (AP) is a device that connects wireless devices to a wired network using Wi-Fi or other wireless standards . APs act as transmitters and receivers of wireless signals and provide wireless coverage for a specific area . APs can operate in different modes such as root , repeater , bridge , mesh , etc . APs can also support different features such as security , QoS , roaming , load balancing , etc . APs can be standalone devices or managed by controllers or cloud services . APs can be verified by using commands such as show ap active , show ap database , show ap bss-table , etc . indicates that the radio is enabled in monitor or spectrum analysis mode. Monitor mode is a mode that allows the AP to scan all channels and collect information about wireless traffic, interference, rogue devices, etc. Spectrum analysis mode is a mode that allows the AP to scan all channels and collect information about RF Radio Frequency (RF) Radio Frequency (RF) is a term that refers to electromagnetic waves that have frequencies between 3 kHz and 300 GHz . RF waves are used for various purposes such as communication , broadcasting , radar , navigation , remote control , etc . RF waves can be modulated by changing their amplitude , frequency , or phase to encode information . RF waves can also be affected by various factors such as attenuation , reflection , refraction , diffraction , scattering , interference , noise , etc . RF waves can be measured by using devices such as spectrum analyzers , power meters , antennas , etc . environment, noise sources, channel utilization, etc. Both modes are useful for troubleshooting and optimizing wireless performance, but they disable normal data transmission and reception on the radio.
The other options are not indicated by a solid amber radio status LED on an Aruba AP because:
Not enough PoE is provided from the switch to power both radios of the AP: This option is false because not enough PoE Power over Ethernet (PoE) Power over Ethernet (PoE) is a technology that allows network devices to receive power and data over the same Ethernet cable . PoE eliminates the need for separate power sources and cables for devices such as IP phones , cameras , access points , etc .
PoE is defined in IEEE 802.3af and IEEE 802.3at standards and supports different power classes and modes . PoE can be provided by switches or injectors that act as power sourcing equipment (PSE) and received by devices that act as powered devices (PD) . PoE can be verified by using commands suchas show power inline , show power-over-ethernet , debug ip device tracking , etc . is indicated by a blinking amber power status LED on an Aruba AP, not by a solid amber radio status LED. A blinking amber power status LED means that the AP is receiving insufficient power from the switch or injector and cannot operate normally. A solid green power status LED means that the AP is receiving sufficient power from the switch or injector and can operate normally.
The radio is working in mesh mode: This option is false because the radio working in mesh mode is indicated by a solid green radio status LED on an Aruba AP, not by a solid amber radio status LED. A solid green radio status LED means that the radio is working in normal mode or mesh mode and can transmit or receive data on the assigned channel. Mesh mode is a mode that allows the AP to connect wirelessly to other APs and form a mesh network without requiring wired connections.
The radio is working the 5 GHz band only: This option is false because the radio working in the 5 GHz band only is indicated by a solid blue radio status LED on an Aruba AP, not by a solid amber radio status LED. A solid blue radio status LED means that the radio is working in dual-band mode and can transmit or receive data on both 2.4 GHz and 5 GHz bands.
References:
https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/ap-led-behavior.htm
https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/troubleshooting/ap-monitor-m
https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/troubleshooting/ap-spectrum

NEW QUESTION # 18
Which feature can network administrators use to centralized RF planning and optimization service when using an Aruba mobility master architecture?

• A. Client Match
• B. AirMatch
• C. Airwave
• D. Client Wave

Answer: B

Explanation:
Explanation
AirMatch is a feature that provides centralized RF planning and optimization service for Aruba wireless networks. It uses cloud-based algorithms and machine learning to optimize the RF performance and user experience. References:https://www.arubanetworks.com/assets/ds/DS_AirMatch.pdf

NEW QUESTION # 19
List the WPA 4-Way Handshake functions in the correct order.

Answer:

Explanation:

Proves knowledge of the PMK
Exchanges messages for generating PTK
Distributes an encrypted GTK to the client
Sets first initialization vector (IV)

NEW QUESTION # 20
The noise floor measures 000000001 milliwatts, and the receiver's signal strength is -65dBm. What is the Signal to Noise Ratio?

• A. 25 dBm
• B. 45 dBm
• C. 15 dBm
• D. 35 dBm

Answer: A

Explanation:
Explanation
The signal to noise ratio (SNR) is a measure that compares the level of a desired signal to the level of background noise. SNR is defined as the ratio of signal power to the noise power, often expressed in decibels (dB). A high SNR means that the signal is clear and easy to detect or interpret, while a low SNR means that the signal is corrupted or obscured by noise and may be difficult to distinguish or recover3. To calculate the SNR in dB, we can use the following formula:
SNR (dB) = Signal power (dBm) - Noise power (dBm)
In this question, we are given that the noise floor measures -90 dBm (0.000000001 milliwatts) and the receiver's signal strength is -65 dBm (0.000316 milliwatts). Therefore, we can plug these values into the formula and get:
SNR (dB) = -65 dBm - (-90 dBm) SNR (dB) = -65 dBm + 90 dBm SNR (dB) = 25 dBm Therefore, the correct answer is that the SNR is 25 dBm.
References: 3 https://en.wikipedia.org/wiki/Signal-to-noise_ratio

NEW QUESTION # 21
Match the switching technology with the appropriate use case.

Answer:

Explanation:

Explanation
USE CASE: a) Controls the dynamic addition and removal of ports to groups Technology: 3) LACP USE CASE: b) Tags Ethernet frames with an additional VLAN header Technology: 1) 802.1Q USE CASE: c) Used to authenticate EAP-Capable client on a switch port Technology: 2) 802.1X USE CASE: d) Used to identify a voice VLAN to an IP phone Technology: 4) LLDP The following table summarizes the switching technologies and their use cases:
Technology
Use case
1) 802.1Q
802.1Q is a standard that defines how to create and manage virtual LANs (VLANs) on a network. VLANs allow network administrators to logically segment a network into different broadcast domains, improving security, performance, and manageability. 802.1Q tags Ethernet frames with an additional VLAN header that contains a VLAN identifier (VID), which indicates which VLAN the frame belongs to1.
2) 802.1X
802.1X is a standard that defines how to provide port-based network access control (PNAC) on a network.
PNAC allows network administrators to authenticate and authorize devices before granting them access to network resources. 802.1X uses the Extensible Authentication Protocol (EAP) to exchange authentication messages between a supplicant (a device that wants to access the network), an authenticator (a device that controls access to the network, such as a switch), and an authentication server (a device that verifies the credentials of the supplicant, such as a RADIUS server)
3) LACP
LACP stands for Link Aggregation Control Protocol, which is part of the IEEE 802.3ad standard that defines how to bundle multiple physical links into a single logical link, also known as a link aggregation group (LAG) or an EtherChannel. LAGs provide increased bandwidth, load balancing, and redundancy for network connections. LACP controls the dynamic addition and removal of ports to groups, ensuring that only ports with compatible configurations can form a LAG3.
4) LLDP
LLDP stands for Link Layer Discovery Protocol, which is part of the IEEE 802.1AB standard that defines how to discover and advertise information about neighboring devices on a network. LLDP operates at Layer 2 of the OSI model and uses TLVs (type-length-value) to exchange information such as device name, port number, VLAN ID, capabilities, and power requirements. LLDP can be used to identify a voice VLAN to an IP phone by sending a TLV that contains the voice VLAN ID and priority.
References: 1 https://en.wikipedia.org/wiki/IEEE_802.1Q 2 https://en.wikipedia.org/wiki/IEEE_802.1X 3
https://en.wikipedia.org/wiki/Link_aggregation
https://en.wikipedia.org/wiki/Link_Layer_Discovery_Protocol

NEW QUESTION # 22
A network technician is using Aruba Central to troubleshoot network issues Which dashboard can be used to view and acknowledge issues when beginning the troubleshooting process?

• A. the Alerts and Events dashboard
• B. the Tools dashboard
• C. the Reports dashboard
• D. the Audit Trail dashboard

Answer: A

Explanation:
Explanation
The Alerts and Events dashboard displays all types of alerts and events generated for events pertaining to device provisioning, configuration, and user management. You can use the Config icon to configure alerts and notifications for different alert categories and severities . You can also view the alerts and events in the List view and Summary view2. References:
https://www.arubanetworks.com/techdocs/central/latest/content/nms/alerts/configuring-alerts.htm 2
https://www.arubanetworks.com/techdocs/central/latest/content/nms/alerts/viewing-alerts.htm

NEW QUESTION # 23
You need to drop excessive broadcast traffic on ingress to an ArubaOS-CX switch What is the best technology to use for this task?

• A. QoS shaping
• B. Rate limiting
• C. Strict queuing
• D. DWRR queuing

Answer: B

Explanation:
Explanation
The best technology to use for dropping excessive broadcast traffic on ingress to an ArubaOS-CX switch is rate limiting. Rate limiting is a feature that allows network administrators to control the amount of traffic that enters or leaves a port or a VLAN on a switch by setting bandwidth thresholds or limits. Rate limiting can be used to prevent network congestion, improve network performance, enforce service level agreements(SLAs), or mitigate denial-of-service (DoS) attacks. Rate limiting can be applied to broadcast traffic on ingress to an ArubaOS-CX switch by using the storm-control command in interface configuration mode. This command allows network administrators to specify the percentage of bandwidth or packets per second that can be used by broadcast traffic on an ingress port. If the broadcast traffic exceeds the specified threshold, the switch will drop the excess packets.
The other options are not technologies for dropping excessive broadcast traffic on ingress because:
DWRR queuing: DWRR stands for Deficit Weighted Round Robin, which is a queuing algorithm that assigns different weights or priorities to different traffic classes or queues on an egress port. DWRR ensures that each queue gets its fair share of bandwidth based on its weight while avoiding starvation of lower priority queues. DWRR does not drop excessive broadcast traffic on ingress, but rather schedules outgoing traffic on egress.
QoS shaping: QoS stands for Quality of Service, which is a set of techniques that manage network resources and provide different levels of service to different types of traffic based on their requirements.
QoS shaping is a technique that delays or buffers outgoing traffic on an egress port to match the available bandwidth or rate limit. QoS shaping does not drop excessive broadcast traffic on ingress, but rather smooths outgoing traffic on egress.
Strict queuing: Strict queuing is another queuing algorithm that assigns different priorities to different traffic classes or queues on an egress port. Strict queuing ensures that higher priority queues are always served before lower priority queues regardless of their bandwidth requirements or weights. Strict queuing does not drop excessive broadcast traffic on ingress, but rather schedules outgoing traffic on egress.
References: https://en.wikipedia.org/wiki/Rate_limiting
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/NOSCG/Content/cx-noscg/qos/storm-control.htm
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/NOSCG/Content/cx-noscg/qos/dwrr.htm
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/NOSCG/Content/cx-noscg/qos/shaping.htm
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/NOSCG/Content/cx-noscg/qos/strict.htm

NEW QUESTION # 24
What is an advantage of using Layer 2 MAC authentication?

• A. MAC identifiers are hard to spoof
• B. MAC allow lists are easily maintained over time
• C. it matches user names to MAC address
• D. No setup is required on the client

Answer: D

Explanation:
Explanation
Layer 2 MAC authentication is a method of authenticating devices based on their MAC addresses without requiring any client-side configuration or credentials. The switch sends the MAC address of the device to an authentication server such as ClearPass or RADIUS, which checks if the MAC address is authorized to access the network. If yes, the switch grants access to the device based on the assigned role and policies. If no, the switch denies access or redirects the device to a captive portal for further authentication.
References:https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/1-ove

NEW QUESTION # 25
Match the phase of message processing with the Open Systems interconnection (OSl) layer.

Answer:

Explanation:

Explanation
Layer: 1) Physical layer Phase of Message Processing: d) Organize the data into bits Layer: 2) Data Link layer Phase of Message Processing: c) Organize the data into frames Layer: 3) Network layer Phase of Message Processing: b) Organize the data into packets Layer: 4) Transport layer Phase of Message Processing: a) Organize the data into segments The OSI model divides the networking process into seven layers, each representing a different step of the transmission chain. Each layer has its own function and is responsible for well-defined tasks. User data passes sequentially from the highest layer down through the lower layers until the device transmits it externally. The lowest layer, the physical layer, converts the data into bits that can be sent over a physical medium. The second layer, the data link layer, organizes the bits into frames that can be transmitted over a link between two nodes. The third layer, the network layer, organizes the frames into packets that can be routed across a network of nodes. The fourth layer, the transport layer, organizes the packets into segments that can provide reliable and error-free communication between two end points12. References: 1
https://www.linode.com/docs/guides/introduction-to-osi-networking-model/ 2
https://en.wikipedia.org/wiki/OSI_model

NEW QUESTION # 26
......

Get Special Discount Offer of HPE6-A85 Certification Exam Sample Questions and Answers: https://certkingdom.vce4dumps.com/HPE6-A85-latest-dumps.html