Verified NSE6_FWF-6.4 dumps Q&As - 100% Pass from VCE4Dumps

Pass NSE6_FWF-6.4 Exam in First Attempt Guaranteed 2023 Dumps!

NEW QUESTION # 21
How can you find upstream and downstream link rates of a wireless client using FortiGate?

• A. On the FortiAP CLI, using the cw_diag -d sta command
• B. On the FortiAP CLI, using the cw_diag ksta command
• C. On the FortiGate CLI, using the diag wireless-controller wlac -d Sta command
• D. On the FortiGate GUI, using the WiFi Client monitor

Answer: D

Explanation:
Explanation
The WiFi Client monitor on the FortiGate GUI shows the upstream and downstream link rates of a wireless client, along with other information such as MAC address, SSID, IP address, signal strength, and connection time. The link rates indicate the maximum data rates that the client can achieve in both directions.
References: Secure Wireless LAN Course Description, page 7; [FortiOS 6.4.0 Handbook - Wireless Controller], page 37.

NEW QUESTION # 22
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?

• A. The wireless network to Internet firewall policy must be configured
• B. Security Fabric and HTTPS must be enabled on the wireless network interface
• C. The new network must be manually assigned to a FortiAP profile.
• D. The wireless network interface must be assigned a Layer 3 address

Answer: A

Explanation:
Explanation
A FortiGate unit is an industry leading enterprise firewall. In addition to consolidating all the functions of a network firewall, IPS, anti-malware, VPN, WAN optimization, Web filtering, and application control in a single platform, FortiGate also has an integrated Wi-Fi controller.

NEW QUESTION # 23
Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?

• A. Areas with the signal strength equal to -68 dB are zoomed in to providebetter visibility.
• B. Areas with the signal strength weaker than -68 dB are highlighted in orangeand red to indicate that no signal was propagated by the APS.
• C. Areas with the signal strength weaker than -68 dB are shown with blackbackground.
• D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.

Answer: D

Explanation:
Explanation
The FortiPlanner site survey reading is a tool that shows the predicted signal strength of the wireless network based on the floor plan, the placement of the APs, and the propagation model. The signal strength is measured in decibels (dB), which is a logarithmic scale that indicates how much power the signal has. The higher the dB value, the stronger the signal.
The site survey reading allows the user to set a threshold value for the signal strength, which is -68 dB by default. This means that any area with a signal strength equal or stronger than -68 dB is considered to have adequate coverage for most wireless applications. These areas are highlighted in green circles on the floor plan. Any area with a signal strength weaker than -68 dB is considered to have poor coverage or no coverage at all. These areas are shown with different colors, such as yellow, orange, red, or black, depending on how weak the signal is.
Therefore, the correct answer is D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
References:
FortiPlanner 2.0 User Guide, page 28
FortiPlanner Data Sheet, page 2
FortiPlanner 2.2 User Guide, page 19

NEW QUESTION # 24
Which statement describes FortiPresence location map functionality?

• A. Provides real-time insight into user usage stats
• B. Provides real-time insight into user movements
• C. Provides real-time insight into user online activity
• D. Provides real-time insight into user purchase activity

Answer: A

Explanation:
This geographical data analysis provides real-time insights into user behavior.

NEW QUESTION # 25
Which statement is correct about security profiles on FortiAP devices?

• A. Security profiles are only supported on Bridge-mode SSIDs.
• B. Security profiles can only be applied to unencrypted wireless traffic.
• C. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
• D. Security profiles can only be applied via firewall policies on the FortiGate.

Answer: C

Explanation:
Explanation
Security profiles are a feature that allows FortiAP devices to apply various security functions to the wireless traffic, such as antivirus, web filter, application control, intrusion prevention, and botnet scanning. Security profiles can be enabled on both tunnel-mode and bridge-mode SSIDs, and can be applied either through the wireless controller configuration or through firewall policies on the FortiGate device. Security profiles can also inspect encrypted wireless traffic, as long as the FortiAP device has access to the encryption keys.
Security profiles on FortiAP devices can use FortiGate subscription services to inspect the traffic, such as FortiGuard Antivirus, FortiGuard Web Filter, FortiGuard Application Control, and FortiGuard IPS. This means that the FortiAP device can leverage the latest threat intelligence and updates from Fortinet to protect the wireless network from malicious or unwanted content.
Therefore, the correct answer is D. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
References:
FortiAP-S and FortiAP-U bridge mode security profiles
Configuring security | FortiAP / FortiWiFi 6.4.2
Security profiles - Fortinet Document Library

NEW QUESTION # 26
Which two statements about background rogue scanning are correct? (Choose two.)

• A. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
• B. A dedicated radio configured for background scanning can support the connection of wireless clients
• C. Background rogue scanning requires DARRP to be enabled on the AP instance
• D. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band

Answer: A,B

Explanation:
To enable rogue AP scanning

NEW QUESTION # 27
Refer to the exhibits.
Exhibit A

Exhibit B

The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?

• A. WPA3 Enterprise
• B. WPA2 Enterprise
• C. WPA2 Personal and radius MAC filtering
• D. Open, with radius MAC filtering

Answer: C

NEW QUESTION # 28
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?

• A. Create a custom AP profile
• B. Preauthorize APs
• C. Create wireless LAN specific policies
• D. Set the wireless controller country setting

Answer: A

NEW QUESTION # 29
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)

• A. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
• B. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
• C. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
• D. DARRP measurements can be scheduled to occur at specific times.

Answer: B,C

Explanation:
DARRP (Distributed Automatic Radio Resource Provisioning) technology ensures the wireless infrastructure is always optimized to deliver maximum performance. Fortinet APs enabled with this advanced feature continuously monitor the RF environment for interference, noise and signals from neighboring APs, enabling the FortiGate WLAN Controller to determine the optimal RF power levels for each AP on the network. When a new AP is provisioned, DARRP also ensures that it chooses the optimal channel, without administrator intervention.

NEW QUESTION # 30
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)

• A. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
• B. DARRP measurements can be scheduled to occur at specific times.
• C. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
• D. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.

Answer: B,D

Explanation:
Explanation
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize
{integer}. Note that DARRP doesn't do continuous spectrum analysis..."

NEW QUESTION # 31
Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)

• A. FortiSwitch
• B. FortiGate
• C. AP Manager
• D. FortiAP Cloud

Answer: B,D

Explanation:
FortiGate, FortiCloud wireless access points (send visitor data in the form of station reports directly to FortiPresence)

NEW QUESTION # 32
Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)

• A. A VAP configured to authenticate locally on FortiGate
• B. A VAP configured to authenticate using a radius server
• C. A VAP configured for captive portal authentication
• D. A VAP configured for WPA2 or 3 Enterprise

Answer: B,D

Explanation:
Explanation
In the SSID choose WPA2-Enterprise authentication.
WSSO is RADIUS-based authentication that passes the user's user group memberships to the FortiGate.

NEW QUESTION # 33
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)

• A. Software security token authentication
• B. Short message service authentication
• C. Social networks authentication
• D. Hardware security token authentication

Answer: B,C

NEW QUESTION # 34
Which two roles does FortiPresence analytics assist in generating presence reports? (Choose two.)

• A. Reporting potential threats by guests on site
• B. Comparing current data with historical records
• C. Gathering details about on site visitors
• D. Predicting the number of guest users visiting on-site

Answer: B,C

NEW QUESTION # 35
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?

• A. SSH
• B. HTTPS
• C. FortiTelemetry
• D. Security Fabric Connection

Answer: D

NEW QUESTION # 36
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit C

A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?

• A. Reduce the number of wireless networks being broadcast by the AP
• B. Install another AP in the reception area to improve available bandwidth
• C. Increase the transmission power of the AP radios
• D. Enable frequency handoff on the AP to band steer clients

Answer: C

NEW QUESTION # 37
......

Fortinet NSE6_FWF-6.4 exam is a certification program offered by Fortinet, a leading provider of cybersecurity solutions. NSE6_FWF-6.4 exam is designed to test the knowledge and skills of candidates in the area of secure wireless LANs. With the rise of wireless networks and the increasing importance of cybersecurity, the NSE6_FWF-6.4 certification has become a valuable asset for IT professionals.

Fortinet NSE6_FWF-6.4 certification exam is designed to test the knowledge and skills of network security professionals in deploying and managing secure wireless LAN solutions. Fortinet NSE 6 - Secure Wireless LAN 6.4 certification is aimed at individuals who are responsible for configuring, monitoring, and troubleshooting secure wireless networks in a variety of environments, including small and medium-sized businesses, enterprise networks, and service provider networks.

Fortinet NSE6_FWF-6.4 Certification Exam is an advanced-level certification program that focuses on the Fortinet NSE 6 – Secure Wireless LAN 6.4 technology. Fortinet NSE 6 - Secure Wireless LAN 6.4 certification is designed to validate the skills and knowledge of network security professionals who are responsible for managing and deploying Fortinet’s wireless LAN solutions. NSE6_FWF-6.4 exam is intended for those who have already achieved the Fortinet NSE 4 certification and have a minimum of two years of experience in network security.

 

NSE6_FWF-6.4 Dumps Full Questions - Exam Study Guide: https://certkingdom.vce4dumps.com/NSE6_FWF-6.4-latest-dumps.html